miniZ v1.8z2 is out!

Hi everyone,

A new miniZ version v1.8z2 is out with improved and increased support for AMD mining – 125,4; 144,5; and ethash/etchash!

For detailed changelog, read below.

Please find miniZ version v1.8z2 @ Download page.

Changelog:

Added AMD support for ETH, for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.
Added AMD support for 144,5, for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.
Fixed support for AMD GPUs, on Windows.
Fixed issues with AMD support for 125,4 (Flux), for Ellesmere GPUs and gfx1031 (RX 6700 XT) GPUs.

OCs for LHR GPUs mining ETH (sudo recommended, in Linux)
We also leave here information regarding the OCs we used for testing (driver 510.54). Note that you may need to adjust a bit for your system. We recommend using sudo in Linux when mining ETH with LHR GPUs.

3060: core: -100, mem:+2990 (Linux)^*, PL=115 W; ~39 MH/s
3070 Ti: core: -200, mem: +4500 (Linux)^*, PL=215 W; ~65 MH/s
3080 Ti: core: +0, mem: +2600 (Linux)^*, PL=266 W. ~79 MH/s (~84 MH/s with proper cooling)

^* On Windows, memory clock with MSI Afterburner should be half of the indicated value. For example, for the 3080 Ti you need to set +1300 for memory clock in MSI Afterburner. Note that you may need to adjust a bit for your system.

*** Thank you all for the feedback! ***

Remember to try --oc1/--oc2/--ocX options for optimum performance.

For additional information check our Usage or FAQ pages.

*** Download miniZ version v1.8z2 here. ***

Engage, feedback and support

Because your feedback is very important, miniZ kindly encourages you to use the comment box below for general questions and feedback.

Certainly we will strive to help you with any doubt and provide a solution to any problem you may encounter. In case you need to reach us, please check the Support page.

On Twitter

Our thread on bitcointalk.org

We wish you a fast and friendly mining experience!

Comments

Baba says:

May 11, 2022 at 12:49 pm

Hi, I was happy with AMD but it still doesn’t support 6600XT at algo 125.4.This version does not change much, but there are no problems Nvidia with 512.12 drivers:CC +250 MC 0power 70w3060ti – 50 Sol/s /flux/3070ti – 70 Sol/s /flux/I hope to add other AMDsoon,Thanks

ZeroII says:

May 16, 2022 at 6:50 am

How can i fix this?************ miniZ v1.8z ************Number of miniZ CUDA>=[8.0] using driver CUDA[0.00] devices found: 1miniZ<144,5>[00:0:00.0:1598]: Selecting GPU#0[0] NVIDIA GeForce MX450[FATAL ] GPU[00] has invalid mode 0.[INFO ] Disconnecting from btg.2miners.com

- miniZ says:
  
  June 1, 2022 at 11:33 am
  
  Hi ZeroII,
  Your gpu is turing… miniZ doesn’t have a kernel for 2GB GPUs with that architecture.
  Cheers
  
Bob says:

June 6, 2022 at 7:44 pm

Are overclock profiles, memclock, cclock, power limit settings, etc able to be set in a config file for windows?

- miniZ says:
  
  June 6, 2022 at 9:59 pm
  
  Hi Bob,
  Not at the moment.
  Also, it will not be implemented in the next release.
  But we’ll work on it for other future release.
  Thanks for the suggestion.
  Cheers
  
Sahil says:

September 6, 2022 at 3:56 am

Hi

can I control the fan speed of GPU by using commands on miner if there can you tell me but without using any afterburner please short this out it would be a great help..

- miniZ says:
  
  September 7, 2022 at 6:12 pm
  
  Hi Sahil,
  Yes, this is possible. Only for Nvidia GPUS.
  On version v1.9z we added --fanspeed option for fan control (NVIDIA).
  If you want the fan to run at 50% you can add --fanspeed=50 to your command line.
  If you are running an old driver, it is possible you may need to update it.
  Also, you need to run the command with Administrator privileges (on Windows), or sudo (on Linux).
  Let us know if this helps.
  Cheers